Universal 12V Brake Switch

1.0 lbs
Rating:  7 reviews
Our Brake Light Kit converts the taillights of your Club Car DS to brake lights! 

Fits Club Car DS 1982 and up (both gas and electric models)

 Kit includes: 
  • A bracket for mounting a microswitch under your brake pedal
  • Microswitches
  • A wiring harness
  • All necessary hardware Instructions included 
Note: Please read our Installation Procedures for Electric Accessories before beginning any electrical work!
Product Rating: (4.00)   # of Ratings: 7   
(You must Login before you can write a review)

5 - Great
4 - Good
3 - OK
2 - Bad
1 - Terrible
0% 50% 100%

Sort: New to Old RE-SORT COMMENTS:

Showing comments 1-10 of 7
1. John on 7/19/2012, said:

No mods needed bolted right up to my cc DS
  (0 people found this comment helpful, 0 did not)
2. Charles on 3/27/2012, said:

Everything was great. The brake switch kiit fit my 2004 Club Cart without drilling. Had to add spacers to raise switch bracket to make proper contact with brake pedal arm. A wiring diagram for complete circuit would have been helpful.
  (0 people found this comment helpful, 0 did not)
3. Robert on 2/12/2012, said:

For me the bigest problem with the brake switches were that they are not made for the cart that I have. I have a 09 Club Car (Presedent), and the brake sys on this cart is no where like the drawing that comes with the switches. This cart has a closed in frame, a plastic pan covering the brake system. There is no way to put two switches on this brakes. There is no way to mount the switch to the back of pedal at all. For the switch under floor, you have to remove the floor mat, then the floor board peice that covers the brake linkage under floor. There is only a rod from the brake pedal back to a cable connection, with a turn buckle for ajustment. Had to brake the locking nut loose and make plate to go between the nut and the adjustment nut (4" in length). I used the switch mount that came with the kit and mounted it on to bacl of the plastic pan that was molded up in the floor bottom.. Then wired it up to two switches for power to cut off the brake switch, turn signal's and another for turning the head & tail lights on/off when the power switch is turned on. If there is any other way that you can look at the Club Car Presedent models, would be alot of help for some other peason down the road that wants to add Brake Light System.
  (0 people found this comment helpful, 1 did not)
4. STEVE on 10/11/2011, said:

on order for 3 weeks i called 2 times on the stop light switch as of 10/11/11 no stop light switch shipped to me. steve
  (1 people found this comment helpful, 0 did not)
5. David on 9/27/2011, said:

Found product to be very good. had to mount under the floor and modify bracket but would use again.
  (0 people found this comment helpful, 0 did not)
6. Dale on 11/22/2010, said:

So much easier to mount under floor than on the brake pedal. I like it because it does not matter where you touch the brake pedal, the brake lights come on.
  (1 people found this comment helpful, 0 did not)
7. Richard on 3/20/2009, said:

Very nice product, but a little tricky to get installed. I mounted it to the bottom of the floor on the underside of cart. Needed to drill holes through deck to secure. 12v power must be connected, and then routed to brake lights.
  (3 people found this comment helpful, 0 did not)
Showing comments 1-10 of 7


Showing products that fit:
Filter products by cart make, or choose 'show all' to see parts for all makes.
Club Car E-Z-Go Yamaha Clear Selection